The function of the fuel supply system of the diesel generator set is to store and filter diesel, and inject diesel into the combustion chamber in a prescribed working sequence with timing, quantity, constant pressure and corresponding injection quality according to the different working conditions of the diesel engine. , causing it to mix and burn quickly and well with air, and finally discharge the exhaust gas into the atmosphere. copyright by:www.hxdlkj.com What route does fuel flow through to achieve fuel supply and combustion? Let’s explore the specific process with Haixing Dynamics. The fuel transfer pump sucks the diesel from the fuel tank, filters out impurities through the filter, and enters the low-pressure oil chamber of the fuel injection pump. The fuel injection pump increases the fuel pressure and injects it into the combustion chamber through the high-pressure fuel pipe to the injector. A very small amount of fuel leaks from the gap between the needle valve coupler in the injector and excess fuel in the low-pressure oil chamber of the fuel injection pump flows back to the fuel tank through the fuel return pipe. Next, let’s take a look at the combustion system

Diesel generator sets that need to operate for a fixed period of time for a long time are called common diesel generator sets. There are three major difficulties in the purchase of this type of equipment, which is to determine the capacity, number and speed of the units. As a professional power generation equipment manufacturer, Haixing Power gives the following suggestions. 1. The capacity of commonly used diesel generator sets is determined based on the long-term continuous operation output power of the unit that can meet the maximum calculated load of the entire project, and the backup unit capacity of the generator set should be determined based on the importance of the load. The continuous output power of a diesel engine is generally 0.9 times the calibrated power. 2. Determination of the number of commonly used diesel generator sets. The number of commonly used diesel generator sets is usually set to more than 2 to ensure the continuity of power supply and adapt to changes in the power load curve. Only when the number of generator units is large can the number of generator units put in be determined according to changes in electricity load, so that the diesel

There have always been great obstacles to the export development of my country's diesel generator sets. On the one hand, there are overseas local trade barriers and technical constraints. On the other hand, we also have our own deficiencies in after-sales and certification. Here, Haixing Power will analyze the main bottlenecks in the export development of diesel generator sets from five aspects.

Recently, Haixing Power has organized its employees to strengthen their professional knowledge learning and actively engage in the work of diesel generator sets, always maintaining full enthusiasm. At present, Haixing Power is in the stage of transformation and upgrading. In order to accelerate the realization of the goal, the company encourages employees to learn about the content of Zichai New Energy's training at the company and study in Zibo last year, as well as the basic knowledge related to the biogas treatment projects currently involved in our company. Undertake in-depth study. In order to increase everyone's enthusiasm, the company will also conduct a weekly test on the learning content, and the test results will be included in the performance salary assessment. In order to promptly solve the problems encountered by everyone during the learning process, the company will arrange dedicated personnel to promptly collect, provide feedback and solve problems that arise during learning. In addition to the existing information, Haixing also encourages employees to search for more rich information through the Internet to carry out learning work and strive to improve their professional quality. At the same time, through learning, we have strengthened our relationship with

Customers' requirements for the function, performance, price, quality, etc. of generator set products are basic requirements. As the competition in the generator set market becomes increasingly fierce, customers are beginning to pursue higher-level requirements - service requirements. Only when the customer service provided by the generator set company meets the new needs of the market can it be recognized by more customers. Therefore, Haixing Power believes that generator set companies should further improve their customer service systems. The specific ways to achieve this include the following four aspects. copyright by:www.hxdlkj.com 1. Ensure smooth information circulation channels. From the problem reported back by the customer to the customer service staff, the problem is solved by the relevant staff, and finally the customer service staff feeds back the problem processing results to the customer. The main line of information transmission in the entire customer service system ensures its smooth flow.

Haixing will explain the specific contents below: 1. Working grounding (1) Reduce the electric shock voltage. For a system with an ungrounded neutral point, when one phase is grounded and the human body touches one of the other two phases, the electric shock voltage is more than 1.7 times the phase voltage; while for a system with a neutral point grounded, the electric shock voltage drops to close to or equal to the phase voltage. Voltage. (2) Quickly cut off the faulty equipment. For systems where the neutral point is not grounded, when one phase is grounded, the capacitance and insulation resistance between the conductors and the ground can form a current path. The grounding current is very small, which is not enough to cause the protective device to operate and cut off the power supply, which cannot ensure personal safety. . For systems with a grounded neutral point, when one phase is grounded

After the diesel oil enters the filter, it passes through the filter paper, collects in the filter element barrel, and then passes through the oil outlet to the fuel injection pump. The impurities and moisture accumulated at the bottom of the casing are released from the drain plug at the lower part of the casing. Judging from this flow direction, everyone should know that the filter has a great impact on the quality of combustion. Combustion determines the final power generation effect, which means that the role of the filter cannot be ignored. Then, during the contact between Haixing Power service personnel and customers, they found that many users and friends easily neglect the maintenance of equipment filters during the maintenance work of generator sets. Let’s take a look at the specific content and learn these precautions. In the next operation, the generator set will show the combustion effect and provide excellent power supply. 1. When maintaining the diesel filter, some users lose the upper and lower sealing rubber gaskets and oil covers of the filter element, so that the diesel oil is not filtered through the filter element and passes through the gap between the filter element and the filter cover.

Diesel generator cooling forms are generally divided into three types: air, hydrogen, and water. The cooling system of a general synchronous generator is closed, and the cooling medium is recycled. 1) Air cooling - Air cooling adopts the method of fan air supply. Cold air is blown against the end of the winding of the diesel generator set, the stator and the rotor of the generator set to dissipate heat. The cold air absorbs heat and turns into hot air. After the air between the stator and the rotor first merges, it is discharged through the air duct of the iron core and cooled through the cooler. The cooled air is then sent into the generator by the fan for circulation to achieve the purpose of heat dissipation. The machines generally use air cooling for medium and small synchronous generator sets. , 2) Hydrogen cooling - Hydrogen cooling uses hydrogen as the cooling medium. The heat dissipation performance of hydrogen is better than that of air. Most large turbine generators use hydrogen cooling. 3) Water cooling - water

How to match the running-in, use and power of a diesel engine (1) Generally, a new or overhauled diesel generator must run in for 60 hours before being put into full load use. To improve the working conditions of various moving parts of the diesel engine and increase the operational reliability and service life of the diesel engine. (2) Running-in should consider the specific running-in plan depending on the purpose of the diesel engine and the towing method. In principle, as the running-in time increases, the speed and load of the diesel engine should be gradually increased in stages. During the entire running-in period, the load should be 50 to 80% of the 12-hour calibrated power, and the speed should not be greater than 80% of the calibrated speed. However, in the initial stage of running-in, the running time under idle operation or too small load should not be too long. Note: Whenever the cylinder liner, piston, piston ring, connecting rod bearing and crankshaft are replaced, a short-term running-in should be carried out according to the above running-in conditions. diesel fuel

Diesel generator sets generally need to change the oil once after 500 hours of operation. However, sometimes the replacement period is not reached, or the oil becomes thinner and impurities increase before it has been used for a long time, making it impossible to continue using it. Why does diesel generator oil deteriorate too quickly? ①. The oil grade is wrong and the quality does not meet the requirements. Generally, diesel generators with supercharged speed and calibrated speed greater than 2000r/min should use CC grade or above oil; ②. Technical status of diesel engine generators Not good, air blow-by, oil blow-by, fitting gap is too large or oil temperature is too high; ③. Diesel engine generators often operate at low temperatures, low loads, and low speeds. The piston deformation is insufficient and combustion is incomplete. Diesel enters the oil pan along the cylinder wall, causing the oil to dilute and deteriorate; ④. Exhaust gas enters the oil pan and condenses into water and Acidic substances will cause the engine oil to deteriorate; ⑤. The oil filter element is dirty, and unfiltered dirty oil enters the lubricating parts, accelerating the wear of parts. ⑥. The filter element sealing ring is broken.